Ref: LX-PA / LX-EP

Compact, low cost, IP40, 0-1250mm wire rope position sensor with analog and digital outputs

  • Low-cost potentiometric cable displacement sensor
  • Measuring range: from 50mm to 1250mm
  • Output signal: ratiometric (30 volts max) or incremental encoder
  • Linearity: ±0.1% (LX-EP) or (±0.25% to 1%) of full scale (LX-PA)
  • Repeatability: ± 0.03% Full Scale
  • Sensor body: Thermoplastic
  • Protection: IP 40
  • Temperature: -25°C to 75°C
  • Lifetime: 125,000 to 2,000,000 complete cycles (depending on range and model)

Download the product sheet

Log in to see the price
Login
?

Introduction

The LX series of cable displacement transducers are designed for linear displacement measurement in industrial environments over strokes from 0 to 1250 mm. With a robust, compact and economical thermoplastic design, the LX series of cable sensors is ideally suited for OEM projects.

2 models are available: LX-PA with analogue output and LX-EP with digital output. Eleven measuring ranges are available, from 50mm to 1250mm.

Specifications

LX-EP LX-PA
measuring range 50mm / 70mm / 96mm / 120mm / 250mm / 390mm / 500mm / 640mm / 750mm / 1000mm / 1250mm 50mm / 70mm / 96mm / 120mm / 250mm / 390mm / 500mm / 640mm / 750mm / 1000mm / 1250mm
Measurement principle Incremental angle encoder Potentiometer
Resolution 0,2 to 0,5 mm infinite
non-linearity 0,10% 0,25 to 1%
Lifetime (no. of cycles) 1 to 2 Millions 125000 to 1 million
Supply voltage 5.00 ± 0.25 VDC 1 - 30 VDC
Output signal 2 TTL signals in quadrature, collector, with 5.4KΩ pull-up resistor 24.8 mV/mm x Supply voltage
Operating temperature -40° C to 75° C -25° C to 100° C
Bandwidth TBD TBD
Weight 85 g 85 g

Installation

The cable is directly or indirectly linked to the displacement to be measured, which allows for non-normal or non-linear displacement. The measurement can be offset by cable extensions. The cable sensor is not necessarily aligned with the displacement.

The standard terminal block can be replaced by an optional connector or cable. The cable end can be customised to facilitate integration with the desired application.

Mounting accessories are also available.

Applications

The LX series sensors are recommended for :

  • OEM development projects
  • integration in limited spaces, applications that require a very small sensor
  • Automotive, speed and acceleration testing
  • suspension travel measurements
  • any other industrial application (test bench, lifting, handling) or robotics
Technologie
Wire rope Position
Etendue de mesure linéaire
50 / 70 / 96 / 120 / 250 / 390 / 500 / 640 / 750 / 1000 / 1250 mm
Measuring range
±51 à ±250 mm, ± 251 à ±2 m
Nonrepeatability
0.03 % FS
Nonlinearity (% FS)
± 1 , 0.5 , 0.25 %
Bande passante (-3 dB)
10 Hz
Analog output signal
non-amplifié, Codeur Incrémental
Température de fonctionnement
-25 to 75 °C
Protection Class
IP40
Tension d'alimentation
10 Vcc
Housing
Plastic

Type of option Available specifications
Measuring range 50mm / 70mm / 96mm / 120mm / 250mm / 390mm / 500mm / 640mm / 750mm / 1000mm / 1250mm
Prestations Calibration / Wiring
Materials Stainless steel cable in a nylon sheath
Length of electrical cable 15cm to 5m
Application cable connector (Mating) Supplied with or without
Changes / Additions Windscreen wiper / Non-standard potentiometer / Cable voltage reduction or increase / Inverted output
Type of cable attachment Pierced ring / Fasteners
  • Display
  • Electrical cable
  • Calibration
  • Wiring

Related products

Capteur de déplacement à câble miniature

ZX-HM - ZX-PA

Miniature cable displacement sensor - 0 to 38 mm - Analogue output
Inductive linear displacement transducer

LIPS P101/X101 - Stand alone

Inductive linear displacement transducer 0-800 mm - IP67 - Stand-alone mounting - ATEX option
potentiometric cable sensor HX series

HX Series

Cable displacement sensor - IP65/68 - 50 mm to 50 m - Analog output
Cable displacement sensor

JX Series

Cable displacement sensor - 50 mm to 2 m
Phone +33 1 46 91 93 32 Contact Contact form Newsletter S'inscrire à la newsletter